Over the last couple of years I have been fortunate enough to replace a lot of my HT gear and need to store my old gear until I am ready to use it in a basement play/family room. The best place (as far as available space) is an un-insulated attic. I am in the north east and tempurature...
I have been living with my Maelstrom in a sealed 22" cube and like it. So far, it performs very well as far as I can tell. I have yet to finish the enclosure (veneer, etc) and have come to conclusion that cosmetically, the enclosure would look better if I had a downward firing driver. It is...
I've searched here and could not find any information, so decided to post. I have been trying to purchase a Sony DVP-CX985 and everwhere I have checked is out. My local Circuit City claims these units are no longer in production do to a mechanical defect with the disc handling. Does anyone...
Thanks to all who emailed or replied with information on selling my DSS equipment. - Reduced Price Sony SAT A2 satelite receiver with original "H" card and remote. System works and was replaced with a DirecTivo unit. $65 shipped or reasonable offer. - SOLD - Hughes GXECBOT Directivo unit...
I am looking to sell the following but, have questions first: Sony SAT A2 satelite receiver with original (HU?) card and remote. System works and was replaced with a DirecTivo unit. Hughes GXECBOT Directivo unit with remote and original (P4?) card. Was working until a brief power failure...
I am considering these two players, Pioneer DV563A vs Onkyo DVSP501. My main consideration is Progressive Scan capabilities. The Onkyo would compliment my NR900 and allow for automatically switching to the DVD input on the NR900 when the 501 powers on. The Pioneer offers SACD and...
I am wondering if anyone has set up the Xbox to act like a Music Server to be used with Onkyo's Netune. What I will be doing is installing a large HD with my MP3's and my most frequently used games loaded on it. Xbox would reside in my AV rack and I would use wireless controllers for...
I know there are a bunch of very informative DIY cable threads, but can't seem to find them. Or, Maybe you can offer some advice. I am looking to rerun all my systems cables, including inwall wiring and would like to make my own cables. Here is what I need: -A/V interconnects...
Well after starting out to build a Tempest 2 1/2 years ago and then changing over to a Maelstrom, I finally have it up and running. The cosmetics are not yet complete. I used a custom sealed design, heavily braced (sixteen internal barces), roughly 24" cube. Net volume is 5.2 cu ft. I used...
Any suggestions on what to tune a 9 cubic foot tempest enclosure to? This will be a ported enclosure to compliment my 5 cu. ft. sealed maelstrom that is just about complete. Thanks -JohnA
My sealed Maelstrom box is coming along nicely with few problems. The few issues I had where easily overcome with help from this board and a little patience on my part.
I am considering how to mount the plate amp and driver. The plate amp will be mounted in a "pocket" located on the rear of...
Can someone post the following for a Maelstrom driver?
1. Bolt circle dimension
2. Mounting screw hole diamter
3. Outside diameter of the mounting flange.
The bolt circle diameter is the diametric dimension that the eight mounting screw holes are located on. This can be measured going...
As I posted in my "Maelstrom finally started" post, I am facing some obstacles screwing into the MDF panel for my Maelstrom subwoofer. I don't have any clamps to build the box and my first attempt on screwing and glueing some internal braces ended in near disaster with the MDF splitting.
In...
After spending months designing and talking about a Maelstrom, I finally found the funds to start the project.
It will be built to the specs I posted some months ago, a sealed "traditional" enclosure with a net volume (before stuffing) of 145 litres. I plan on using 7 1/2 lbs of polyfill...
I had decided to use the Adire AVA250 for my Maelstrom project becuase of it's features (auto on, phase control and cross over, configuration-plate amp).
However, I would like a little more power. Any suggestions of other amps to look at?
Thanks
-
I am interested in the Niles Remote Anywhere kit. I would like to hear feedback from those that have it.
Did it work well?
Where did you buy it and what was the best price you found?
Thanks
-
I have been contemplating picking up Johnny Nemonic and AirforceOne and didn't for these reasons, JN was too pricey in my opinion and AirforceOne was a flipper.
The Price of NM went from $29.99 to $9.99 and at the same time I saw the superbit versions announced.
Having liked the StarGate movie...
I am looking for a list of all known receivers due this fall with DTS-ES matrix and discreet, DPL2, THX-EX as well as DD and DTS 5.1.
Thanks in advance
-JohnA
I am looking for more info on the TX-DS797 and TX-DS898 being released in September, seewww.twice.com for reference
Does the 898 have an upgradeable DSP like the 989? Will the 898 include the new LCD remote?
Any information is appreciated.
Thanks
I have finalized the specs on my DIY tempest, a 202 litre (net) enclosure tuned to 17HZ, Thanks to alot of personalized help from Dan Wiggins at Adire and this messageboard.
I had finally settled on the AVA250 to power the sub because of the excellent price/performance ratio.
I recently...
I am putting the wraps on finalizing my Tempest plans and am now left with the enclosure materials.
Adire Audio recomends void free birch plywood as first choice, I have seen many people recomend the MDF over the ply. Adding to the confusion is the recomendation to use teh ply for bracing and...
I will be starting my Tempest Subwoofer soon and was wondering, what do I cover screw heads with after box assembly?
Wood putty, fiberglass...?
Thanks
-JohnA
I will be using void free birch plywood as suggested by Adire for their reference designs.
The question I have is do I need to use T-Nuts with plywood or can I just mount the driver by screwing directly into the plywood.
Thanks
-JohnA