Up for sale is my earthquake maker Adire Audio Tempest 15" Subwoofer that I custom made in black ash. It is 49" wide, 20" tall with rubber feet, and 18" deep. The enclosure is a net 218L (7.7cf) enclosure and has variable tuning via its dual 3" flared ports. In maximum output mode (both ports...
Originally sold for ~$130 from parts express. I have used this with my Adire Tempest 15" custom sub until I upgraded to a Rythmik 350w amp. This amp puts out 270+ watts into a 4 ohm load. Made more than enough power to push my tempest. Asking $100 shipped OBO. Pictures on request. Thanks.
This is the original Tempest that started it all. It is just a second driver i have laying around and don't have a room big enough to need 2 of these subs. My loss your gain. Build a 8cf enclosure tuned to ~18hz and you will have a MONSTER HT sub. I build a similar one for my music only system...
Is there anyway to split the signal between subs? I have an 8" subwoofer that is flat to about ~27hz, and i want to incorporate an adire tempest 15" to cover the duties below that. How would this setup be possible without buying any expensive equipment? my receiver does have decent bass...
Not a scratch on them. Not even broken in yet. I don't use them as much as I thought I would. I still use my Mirage's alot more often. It consists of a mint pair of Onix XL-S speakers. A pair of Athena As-p300 8" 100 watt sub-woofers. This is a great almost full-range system. I bought the Onix...
Has less then 30hrs on the original bulb. I don't use it at all anymore. I will let it go for $550 shipped. Comes with original box and manual with remote and cables. Here are some pictures: http://i2.photobucket.com/albums/y46/benihana/plv4.jpg...
I have a 230L sealed tempest. I want to convert this to ported, similar to the adire alignment. However, I need to know how to approach this. First question is, is the 230L LowQ model volume before or after driver displacement? I also have the amp built into the side, so i'm guessing that will...
I have this amp from PE, it has no bass boost, and the rumble filter is at 19hz. Is there anyway I can lower this to 14hz without enabling any boost? In the manual it only shows the 14hz rumble filter enabled with 1db of boost at around 20-24hz.
Hi. I'm selling a used Adire Shiva MKIII 12" driver. 3 of the tinsel leads were torn apart, but they were repaired, and all else is in great condition. Paypal preferred. $75 shipped takes it.
k here goes... I have my main speakers biamped by having one amp for each speaker vertically biamped. And now that I have the mains crossed over at 80hz, will it only send signals above 80hz to the outboard amps, therefore releaving stress on the amps because they don't have to play the bass...
I have a Soundstream/Krell DAC-1 as my DAC for my cd player, now that I bought a Denon DVD-1910 that has Burr Brown 192/24 DAC's in it, will it sound better than the soundstream, anybody familiar with it? Thanks.
I noticed that when I have svideo out fromt he receiver to the tv, and then using my dvd player with composite, i get some fuzzy lines, does this upconvert the signal from 200 lines to 400, or does it just allow me to view the signal in only composite form, and will i notice a difference if i...
I have a seald version of this sub , it is the Adire .577 alignment. Now i want to port this, but i don't know if i can fit flares in there because the design is different than the vented designs. Will it be ok if i go with straight pipes and how big would the ports have to be?
Will the MCACC/EQ adjustments on the VSX-1014tx be enough to do what the Behringer feedback destroyer does as far as EQing the sub to the room? and is the bass management good enough to not warrant a purchase of the OUTLAW ICBM??
Right now I have a 230L Sealed Adire Tempest. What kind of improvement will I see if i bump up to a PB2 PLUS?? And how would a PB2 Plus compare to a ported Adire tempest?? Thanks.
I have 2 amplifiers that i am currently vertically bi-amping my main speakers with . They are Audiosource Amp Three's running Mirage M-3si speakers. My question is that will it be better to monobridge them and have 400 watts to each speaker as opposed to the 150 watts supplied to each low and...
Is it possible just to use the ICBM as a 2 channel crossover? I have a prologic Yamaha RX-v870 feeding 2 outboard amps into my Mirage M-3si speakers, and i also have a 230L sealed Tempest that i'm trying to seamlessly blend in. It seems like the M-3si play low enough to where the subwoofer...
What does the LOW Q sealed 230L tempest with 250 watts compare too in the retail market subwoofers. I have yet to hear a sub that can match it from all the stores I had went too, but the Klipsch RSW-15 @ goodguys seemed to have similar output, but thats like a $1800 sub.What else is there? Oh...
How do send an old amp a signal from the LFE input? I have an extra amp that doesn't have preamp inputs, and i'm wondering how i can get it to receiver a signal, Thanks.
Hey guys, if it wasn't for you guys, i wouldn't have this monster of a sub. Super clean and accurate, and packs a MIGHTY punch. I never thought i could get bass like this from a sealed sub, it LITERALLY does its magic, i can feel this thing as if it was built in to my body. Next I will get a BFD...
What happens when you are building a box, and one of the sides is like 1/8" short, what can i use to fill in this gap?? Should i get a real thin piece of wood and glue it between both sides? .Thanks.
Is the 272 watts of the PE amp enough to get the tempest going. I want a low Q sealed design for music, and i want to know what kind of box i should build(from your suggestions), and if i will need more amplifier power. My speakers are down -2db @ 30hz, so i want that really low, hence wanting a...
Hey guys, I'm new here, and i have a question. I have a Sony SA-WX700(really impressed by this one), and I need to figure out a way to get this thing crossed over to like 30hz, what kind of crossover will do this?? This thing goes very deep, but my main speakers go deep enough, and I just want...