1. Guest,
    If you need help getting to know Xenforo, please see our guide here. If you have feedback or questions, please post those here.
    Dismiss Notice

Vizio VP322 32" Plasma stand screws

Discussion in 'Displays' started by ryan-w, May 5, 2014.

  1. ryan-w

    ryan-w Active Member

    Joined:
    Feb 10, 2005
    Messages:
    40
    Likes Received:
    0
    Does anyone know what size the screws for the stand on the Vizio VP322 TV are?? I had this TV hung for years and now want to move it to a room where it'll be on a desk so I need to use the stand....I have the stand but no screws. Anyone have any idea what size they are, I can't find this info anywhere??

    Thanks in advance.
     
  2. Jason Charlton

    Jason Charlton Ambassador

    Joined:
    May 16, 2002
    Messages:
    3,400
    Likes Received:
    316
    Location:
    Baltimore, MD
    Real Name:
    Jason Charlton
    Check the manual, page 6.
     
    Gregg Loewen likes this.
  3. ryan-w

    ryan-w Active Member

    Joined:
    Feb 10, 2005
    Messages:
    40
    Likes Received:
    0
    In the manual, it just states the length of the screws where the mount would go, it doesn't give the sizes for the screws for the stand....Any idea??

    Page 6 of the manual says:
    Unplug all of the cables and cords
    from your VIZIO VP322 Plasma
    HDTV10A.
    2. Place the VP322 PLASMA face down
    on a soft and flat surface (blanket,
    foam, cloth, etc) to prevent any
    damage to the TV.
    3. Remove the four (4) screws holding
    the base to the VP322 PLASMA.
    4. Carefully remove the stand base.

    Now, the VP322 Plasma HDTV10A can fit
    securely to a mount (sold separately) by
    utilizing the mounting holes in the center of
    the back panel of the High Definition TV.
    Please make sure to read the instructions of
    your specific mount to properly hang the
    VP322 Plasma HDTV10A.
    The pitch of the mounting holes is 400mm
    horizontally and 200mm vertically.
    The screw type required is metric M6, 20mm
    long, 1.0mm pitch. The length of the screws
    will depend on the thickness plate being
    attach to the TV; our brackets come with
    different length screws.
     
  4. Jason Charlton

    Jason Charlton Ambassador

    Joined:
    May 16, 2002
    Messages:
    3,400
    Likes Received:
    316
    Location:
    Baltimore, MD
    Real Name:
    Jason Charlton
    Sorry, I misread your post and thought you needed screws for the mount, not the stand.

    I think your best bet will be to go to a hardware store and pick up a few at a time until you find one that fits. Chances are, if the mount screws are metric, that the stand screws will be, too. The mount takes M6 screws. The "6" indicating the diameter (I'm pretty sure all "M6" screws have a pitch of 1mm).

    Hopefully, you can judge if the stand screw should be thicker or thinner, then pick up an M5, M7, etc. Should only be a few cents each. Get them plenty long enough. Hopefully the process won't take too many iterations...

    Wish I had a better option, but I can't even find a detailed parts list for that stand (part #3832-0022-0304R).
     
  5. ryan-w

    ryan-w Active Member

    Joined:
    Feb 10, 2005
    Messages:
    40
    Likes Received:
    0
    No problem, I appreciate the help. That's the part # I keep seeing as well and it's for the stand with the screws, nothing to find just the screws. My only real concern is the depth, wouldn't want to take out the board behind there...
     
  6. schan1269

    schan1269 HTF Expert
    HW Reviewer

    Joined:
    Jul 4, 2012
    Messages:
    17,038
    Likes Received:
    894
    Location:
    Chicago-ish/NW Indiana
    Real Name:
    Sam
    If the stand itself has the screw ins, take it with you. My local Do It Best has a "figure it out" screw and bolt set up. As do most actual hardware stores.Note, hardware stores, not home improvement, will have them.
     
  7. ryan-w

    ryan-w Active Member

    Joined:
    Feb 10, 2005
    Messages:
    40
    Likes Received:
    0
    We have an ACE Hardware by me, I'll bring it there and see what I can find out. Thanks a lot.
     

Share This Page