Alright, I'm about to purchase one of those electronic pest controllers which reportedly utilize wiring to produce a 25,000 HZ signal that "drives away the pests." I'm trying to figure out if it is putting a pulse interval within the wiring will that impact the my amp? I have it running through...
I've got the following available for trade. Rushmore (non-CC) - TRADED Apocalypse Now (original) Buena Vista Social Club The Contender Judgement Night Trespass Stewart Little (Sealed BB PVT)- TRADED The Tailor of Panama (BB PVT)- TRADED Little Rascals - All 12 Volumes (sealed 6...
I have an AV12 sub with the PE 250W plate amp (thank you Ryan Schnacke) that I recently completed, that has developed what appears to be a ground loop hum. I've purchased all of the Paladin crimping equipment and was looking to make my own cables. I was thinking about using the LV-77S for my...
Peter, FWIW, I'm running a downfiring sub and had the rattle. Again. Its premature for me to say that it's attributable to the driver. It may be the wiring or something else. But, I'll figure it out. Bryant
Peter, I just got my sub together for a trial run and I noticed the exact thing around 50 Hz. I thought that it was the wires from the amp hitting the speaker until you said something. As I said, I still haven't put the final touches on it so i didn't worry about it too much..... until now...
Down to the last few steps and I really didn't see this presented anywhere. I'm using a 4" PVC port 20.5" long for my AV-12 enclosure. I'm just trying to determine what is the best way to affix the port to the MDF baffle? My design is downfiring with the port venting to the bottom as well...
Great purchase, mine should be here in a few days.
FWIW, I'm going with 4.0 ft3 vented enclosure tuned to 19Hz.
Also, according to John, the cut size for the driver is 11". The countersink diameter for the outside of the basket would be 12.5". In case you want to get started before the...
Forgive my ignorance, but I'm a little confused. Why would the XTR DVC freak out with 250 @ 2ohms when the spec sheet I have in front of my indicates 800 Watts Pmax at 2 ohms. I show Fo at 23.57Hz and Vas at 5.54 according to manufacturer specs.
zUIfgerho;
dsgvsadh'o dasfho'...
Ron, I used your driver specs and the volume you had in WinISD and came up with the port size. I used a volume of 212 L to account for the fill material. I noticed after I posted that you were looking for something around 18Hz. If you want that, it appears that you'll need to increase the...
I guess you could tune to 20 Hz with a 8.42 inch (4.02 diameter) port. Assuming the fill material would pseudo-create a volume of ~212 L. I think that I read somewhere that the law of deminishing returns kicks in for enclosures over 5ft3 at 20% in a 1lb/1ft3 ratio.
Thanks Patrick for the...
I've searched a lot of threads and can't seem to find the answer that I'm looking for, so here goes. I have an Orion XTR 12" (DVC)driver that I plan on wiring parallel in a vented enclosure. Using WinISD, it seems to me that a 147L enclosure is optimum when tuned to 27Hz. So can I effectively...
I'm looking at getting a complete system up at the Reference dealer in Kenora, ON. I believe the store is called NORTHERN SOUNDS AND SYSTEMS. Does anyone know who I could talk to, to get a great deal? FWIW, I'm looking at getting Studio 100's Studio 40's Studio CC Servo 15 Any help...
First off, I have no idea what I'm doing. I'm looking at getting a new tv and pc. So any suggestions for equipment are greatly appreciated. I'm looking for the system to serve as my primary pc, hometheater and tv. Questions: 1. What requirements are there for the tv for my to use it as a...
In framing our house, I had several wire groups put in. On one side of the room, I've got 2 Cat5, 2 pair of speaker wire. On the other, I've got 1 Cat5, 1 RG6 and 2 pair of speaker wire. At the front of the room, I've got the four pair of speaker wire and 1 RG6 line. My question is this...
Thanks Todd, they've got a 1,000 ft. spool of Cat5e @ Home Depot for 53.00. I just kept seeing Plenum wire everywhere and never knew what the difference was.
While we're in the process of finishing our house, I would like to run Cat 5 wire to each room. My questions is, if I'm not planning on running the wire through AC ducting, do I need plenum rated wire?
I'm not worried about the extra 80 bucks to get plenum rated wire, but didn't know if its...
Chris - I guess it depends on how thick the insultation is. I found the stud and drilled a hole next to it, anticipating a small gap in the insultation next to the board. I used one of those small beaded chains (like what's in the toilet tank) and lowered the chain. I then used a strong magnet...