Recent content by MichaelAngelo

  1. MichaelAngelo

    Question about PR displacement vs driver displacement

    Give it a whirl Frank. PR's can be used in cars- Kicker had a line of boxes ~20 yrs ago with PR's in them, a 8" woofer w a 10" PR, and a tweeter on top. Had some in a truck.
  2. MichaelAngelo

    Kicker L7 HT sub

    I like the slot port, whats it tuned to ?
  3. MichaelAngelo

    Kicker L7 HT sub

    Jasen, I had 2 S15L5 in big sealed boxes for HT, they soak up the watts. I had a PE plate amp (270 watts) on ea VC, and never bottomed them. Sold one to buy an AV15, and tho the AV15 will bottom with a PE amp on ea coil and the Solo wont, the AV sounds SOOOO much better than the Solo, I hope...
  4. MichaelAngelo

    WTB: ATI 9700 Pro

    I have a 9700 pro, with a dvi-vga adapter etc but its been volt modded. I can return the card back to stock easily, have stock heatsink etc. but I live in Texas, that kills the local requirement. :) FWIW, if ya want a screamer, I'll leave it volt modded, as it does 415-425 on core, with...
  5. MichaelAngelo

    How to set up 4 subs?

    FWIW when I clicked that link it goes to optimumonlinedotcom, not harmon dot com. HTH
  6. MichaelAngelo

    amplifer

    :) Wayne, looong ago, when the I saw the Carver cube amp for the first time, (car audio was not as bigas today) I remember thinking, "In my truck??' and grilling my electrician father, 'Dad, how big a convertor would I need for an amp this big?' His answer- No. :)
  7. MichaelAngelo

    Can the PE 300-794 plate amp be used with a 2 Ohm load?

    Javier, I see you live in Mexico City- hotter than Beaumont !! I have 2 of the 300-794 amps running 2 ohms, 1 into each voice coil of an AV-15. Room temmp stays at 68-70F, but I didn't mount the amps to the sub enclosure. I have them mounted in a vertical row, on a standoff fromm the wall. A...
  8. MichaelAngelo

    Plate amp ground loop problem

    Eric, I had a similar problem with my cable. After some Googling, I found a tip that worked for me. I ran the cable line into 2 75-300ohm converters back to back 75-300-back to 75. I used the little "pigtail" type. This cured my hum. I don't know if it will work with satellite though-worth a...
  9. MichaelAngelo

    front vs rear mounted ports?

    I seem to remember several threads from some time back discussing acoustic coupling. The consensus seemed to be that drivers arranged close together have greater output than if summed seperately; does this hold true for a port too? IOW, does a port acoustically couple with the driver? I'm...
  10. MichaelAngelo

    Looking for: AV-15 Subwoofer Speaker

    It will bottom out w 1000 watts, be careful with the volume knob.....
  11. MichaelAngelo

    Whats the purpose of square subs?

    Brian, I believe the square subs are measured on a side. My 15 inchers measure 15x15 in sq.
  12. MichaelAngelo

    Whats the purpose of square subs?

    Hank, I get what you're saying about the area of a circle. :) I'm not trying to promote Kicker, but their reason given for square subs is this: Round subs would have a roughly diamond shaped gap between them, mounted on a wall in a car (or van, most likely, for campetition use,)whereas...
  13. MichaelAngelo

    Whats the purpose of square subs?

    linkage : :) In an A-B comparison to even a "good" subwoofer, such as the AV15, the Solobarics lose. But as HT subs, I cross mine over at 40hz, they slam. Too boomy tho really- they definitely are meant for auto use. Buddy of mine has 2 of the 12 inchers in an Infinite Baffle, not...
  14. MichaelAngelo

    Whats the purpose of square subs?

    Hi all ! Re the square Solobaric subs, I have a pair of 15 inch Solos in a common 24 cu ft box. Kicker states the square design was to help acoustic coupling, in competition automotive installs. Square subs maximize cone area on the mounting surface; circles would have greater "gap" between...
Top