Jump to content



Sign up for a free account to remove the pop-up ads

Signing up for an account is fast and free. As a member you can join in the conversation, enter contests and remove the pop-up ads that guests get. Click here to create your free account.

Photo
- - - - -

Pioneer vsx1121 speaker ohm setting


This topic has been archived. This means that you cannot reply to this topic.
3 replies to this topic

#1 of 4 OFFLINE   KenY

KenY

    Extra



  • 24 posts
  • Join Date: Feb 08 2012

Posted February 27 2012 - 06:14 AM

Anyone have trouble getting to the speaker ohm setting mode when following the manual? I can't seem to get it to work...thanks!

#2 of 4 OFFLINE   John Garcia

John Garcia

    Executive Producer



  • 11,550 posts
  • Join Date: Jun 24 1999
  • Real Name:John
  • LocationNorCal

Posted February 27 2012 - 06:19 AM

Unless all of your speakers are 4 Ohm and demanding to drive, you should leave the receiver in 8 Ohm mode.
HT: Emotiva UMC-200, Emotiva XPA-3, Carnegie Acoustics CSB-1s + CSC-1, GR Research A/V-1s, Epik Empire, Oppo BDP-105, PS4, PS3,URC R-50, APC-H10, Panamax 5100 Bluejeans Cable
System Two: Marantz PM7200, Pioneer FS52s, Panasonic BD79
(stolen) : Marantz SR-8300, GR Research A/V-2s, Sony SCD-222ES SACD, Panasonic BD-65, PS3 60G (250G)

Everybody is a genius, but if you judge a fish by its ability to climb a tree, it’ll spend its whole life believing that it is stupid.” – Albert Einstein

 


#3 of 4 OFFLINE   KenY

KenY

    Extra



  • 24 posts
  • Join Date: Feb 08 2012

Posted February 27 2012 - 10:58 AM

Yes, I know, but that's not my point...I just wanted to look at it. I know the default is 8 ohms, and my speakers are 8 ohms. I just wanted to look at it because I'm enjoying fiddling with my new receiver while I await the arrival of my wife's bookshelves to put my rear speakers on...I just couldn't get it to go into that mode.

#4 of 4 OFFLINE   gene c

gene c

    Producer



  • 5,734 posts
  • Join Date: Aug 05 2003
  • Real Name:Gene
  • LocationBay area, Ca

Posted February 27 2012 - 11:14 AM

I just used the same procedure on my vsx-23 and it worked fine. I found using the remote control easier than the Tune and Preset buttons on the front panel. Just to clarify. Press and hold the Enter button on the front panel and then push the Power-On button. It will say Factory Reset-No. Use the Up-Down buttons on the remote to change the mode and when you get to the Ohm mode you would use the L-R buttons to make any changes.
"Everyday room": Panasonic 58" Plasma, Dish HD DVR, Pioneer Elite vsx-23, BDP-23 BR, dv58avi universal dvd player, Paradigm Studio 20 V1, CC-450, Dayton HSU-10 subwoofer.

"Movie/Music room": Toshiba 65" DLP, Dish HD receiver, Marantz 7005, CC-4003, BD-7006, Polk LSI25's-LSi7's-LSiC, 2 original Dayton 10" "Mighty-Mites" subwoofers. (subject to change without notice).
 
Also have  MB Quart Vera VS05 +.....too much to list. Help me.