1. Guest,
    If you need help getting to know Xenforo, please see our guide here. If you have feedback or questions, please post those here.
    Dismiss Notice

Projector Mount and Drywall Question

Discussion in 'Home Theater Projects' started by Torgny Nilsson, Jan 14, 2004.

  1. Torgny Nilsson

    Torgny Nilsson Well-Known Member

    Joined:
    Jan 8, 2003
    Messages:
    255
    Likes Received:
    1
    Can someone tell me whether I can attach my projector to my drywall ceiling using molybolts rather than attaching the mount directly to the studs as it says in my mount manual? I don't have studs where I need to install the projector and I don't have an attic that I can access to reinforce the ceiling above the projector.

    Has anyone done the same thing? The projector is only 6.8 lbs (plus the weight of the mount) and I assume I will be okay as long as I use molybolts that can hold up to 30 to 50 lbs.

    Thanks.
     
  2. Erik Farstad

    Erik Farstad Well-Known Member

    Joined:
    Jan 28, 2001
    Messages:
    560
    Likes Received:
    0
    Yes, you'll be fine using moly's....just make sure you use the appropriate size and depth for your application.

    E
     
  3. Darren{Moo}

    Darren{Moo} Member

    Joined:
    Jul 10, 2003
    Messages:
    23
    Likes Received:
    0
    From the been there, done that department, my advice would be to cut the drywall and install a framing member. Drywall repair cheap....Projector repair expensive.....

    YMMV
     
  4. Ron-P

    Ron-P Well-Known Member

    Joined:
    Jul 25, 2000
    Messages:
    6,285
    Likes Received:
    0
    Real Name:
    Ron
    Why not build a small mounting plate that will span the distance between two joists. You can lag-screw the plate to the joists and then mount the PJ to the plate. That's what I did.

    [​IMG]

    It may not look as clean as a direct mount to the drywall, but it's 100x more solid.


    Peace Out~[​IMG]
     
  5. Erik Farstad

    Erik Farstad Well-Known Member

    Joined:
    Jan 28, 2001
    Messages:
    560
    Likes Received:
    0
    Duh...great point Ron...I too did the same thing, built a mounting plate. :b But I guess I was too focused on answering Torgny's question, I missed the obvious! LOL....
     
  6. Torgny Nilsson

    Torgny Nilsson Well-Known Member

    Joined:
    Jan 8, 2003
    Messages:
    255
    Likes Received:
    1
    I decided to take your collective advice and am building a mounting plate. More work, but more peace of mind as you have mentioned. Thanks for the help.
     
  7. Randy Emery

    Randy Emery Member

    Joined:
    Jan 16, 2004
    Messages:
    13
    Likes Received:
    0
    message deleted
     
  8. Shane Burton

    Shane Burton Member

    Joined:
    Mar 12, 2002
    Messages:
    23
    Likes Received:
    0
    Drywall is more than sufficient, as long as you use a mounting plate that spreads the load out.

    Shane
     
  9. Randy Emery

    Randy Emery Member

    Joined:
    Jan 16, 2004
    Messages:
    13
    Likes Received:
    0
    Yes, the drywall would not particiate structurally
     
  10. marc_manny

    marc_manny Well-Known Member

    Joined:
    Nov 25, 2003
    Messages:
    55
    Likes Received:
    0
    Go to Home Depot and buy at ceiling fan mount. They have ones for new construction and ones for remodeling. You want the one for remodeling, so basically you cut out a small hole in the ceiling and then fit the entire unit up into it. There are expansion nuts on each side that you screw (kind of like a shower rod) to tighten between the studs. Then you can just secure the projector to the ceiling box. They are rated for like 30 pounds or more.

    Marc
     
  11. Ron-P

    Ron-P Well-Known Member

    Joined:
    Jul 25, 2000
    Messages:
    6,285
    Likes Received:
    0
    Real Name:
    Ron
    Marc, do you know if those mounts are hollow up the center and have a large enough diameter to allow cables up through? Make for a nice clean look if so.


    Peace Out~[​IMG]
     
  12. CRyan

    CRyan Well-Known Member

    Joined:
    Feb 9, 1999
    Messages:
    1,244
    Likes Received:
    0
    Hey Ron. They are not big enough for a DVI cable. However, they can be cut faily easily to accomodate several sets of cables. I was thinking of using these myself until I changed my mounting plan. Very easy, especially if you have access above the ceiling.


    C. Ryan
     
  13. marc_manny

    marc_manny Well-Known Member

    Joined:
    Nov 25, 2003
    Messages:
    55
    Likes Received:
    0
    Hey Ron,

    They have nickel size holes (the ones I have used), so like C.Ryan said you probably won't get a DVI cable through it. It would be worth while to take a look and see if they have any with bigger holes, or maybe you could cut enough out for a DVI connector to fit through without loosing structual integrity(sp?).

    They are definately easier if you have access to above the ceiling, but it can be done from below also.

    Marc
     
  14. CuZ06

    CuZ06 Active Member

    Joined:
    Dec 11, 2001
    Messages:
    26
    Likes Received:
    0
    Real Name:
    JC
    Use the adaptor plate with dry-wall cutout......
     

Share This Page