Home Theater Forum  ›  Forums  ›  Home Theater Hardware  ›  Display Devices (TVs/Projectors)  ›  1.78:1 vs. 1.85:1
Hey There!

Thanks for checking out our community! We've got lots of great stuff going on around here... why don't you create an account and join the fun? Why?

1.78:1 vs. 1.85:1

#1
Rating: 0
Which projection screen would be better? I enjoy 2.35:1 material, but I do not want to spring for the anamorphic lens. I can deal with the black bars but I am unsure of the picture difference between 1.78:1 and 1.85:1. Any suggestions?
Export to Wiki
#2
Rating: 0

Re: 1.78:1 vs. 1.85:1

The difference itself between 1.78:1 and 1.85:1 is very slight. Those who bother to correct for it do so using height and width controls on the TV or projector.

The official aspect ratio of wide screen TV is 1.78:1.

Very few movies are actually shot as 1.78:1 but many were and are shot at 1.85:1.

Video hints:
http://members.aol.com/ajaynejr/video.htm

.

Export to Wiki
#3
Rating: 0

Re: 1.78:1 vs. 1.85:1

I have posted this same subject a couple of times and get no good response. What will the projectors do. Is is easier to manipulate to a 1.78:1 or to a 1.85:1. In other words would it be better to make the picuture bigger or smaller.
Export to Wiki
#4
Rating: 0

Re: 1.78:1 vs. 1.85:1

I'm not sure exactly what your getting at, but in reality it probably doesn't matter a lot.

Almost all HDTV is/will be 1.78, most HT projectors are 1.78 so that would seem to be a down/dirty best answer if you are looking for a set that will be used primarily for TV viewing.

Even assuming you are interested in Movie Only, the true difference in the screen size for 1.78/1.85 is virtually nil. At a 50 inch screen height you are talking about 3.5 inches in width. From the typical/usual optimum viewing distance calculators, the Field of Vision difference will be almost indistinguishable. Translated an approximately 50 inch height screen is 102in diagonal for 1.78 and 104 inch at 1.85 looking at Carada's website.

If you decide have a letterbox/pillarbox presentation or eliminate 1/2-1 inch borders from the top/bottom or sides by using the zoom in/out on any 16:9 projector I think it's likely a wash in terms of picture quality. The choice of overscan variations among projectors likely would make a sinficantly bigger impact than the 1.78/1.85 decision.

If you decide to go to a constant height setup with a 2.35:1 ratio screen then it beomes much more of an issue. I personally find I notice the lateral dark borders much less watching 4:3 material on a 16:9 set than I noticed the top/bottom borders watching widescreen material on a 4.3 set and I am a pretty big OAR advocate so it never bothered me to watch letterbox material at all.

"I sit in my cube with my headphones on and try to let my competence hold back the tide for as long as possible, then move on when the flood of stupidity breaches the levee. I'm a refugee from Hurricane Stupid."

Export to Wiki
#5
Rating: 0

Re: 1.78:1 vs. 1.85:1

Is this for a film projector or a video projector? I am guessing it will be a dlp, or lcd, video projector so then go with 16:9. If you are really rolling in money and are putting in a film projector then go with 2.35:1.

I would recommend a Stewart.
WELCOME TO STEWART FILMSCREEN
Export to Wiki
#6
Rating: 0

Re: 1.78:1 vs. 1.85:1

As noted very few films (DVD or Blu-Ray) are shot in 1.78:1 aspect ratio - so really 1.85:1 is defacto HDTV.

Personally - I want what the director and editor wanted. I don't care if that is 1:1 or 2.40:1 - I want to see what they created and what got all the fuss up at the theater.

For years I have bought nothing but widescreen additions (DVD). And when I see an 'upgrade' I replace DVD's as a can.
...gene

Receiver: Yamaha RX-V890
HDTV: Vizio SV420XVT
DVD Player: Sony DVP-NC615
Blu-Ray Player: Panasonic DMP-BD60
Cable Box: Motorola DCT6412 (Comcast)Center Speaker: Infinity RS-VideoL/R Speakers: Infinity 625Rear Speakers: Infinity 325Subwoofer: Klipsch SW-8 II

Export to Wiki