Quick question? Can you use any rca cable for digital coax?

Discussion in 'Beginners, General Questions' started by MarkSchro, Sep 15, 2006.

  1. MarkSchro

    MarkSchro Stunt Coordinator

    Joined:
    Oct 19, 2005
    Messages:
    62
    Likes Received:
    0
    My friend asked if he could use any rca cable for a digtial coax signal.
    I thought any rca cable would work and not to buy a $30.00 digital cable.
    He was just going to connect from his cabel box to reciever for his digital
    audio. Can anyone let me know if I am right. Thanks.
    Mark
     
  2. JeremyErwin

    JeremyErwin Producer

    Joined:
    Feb 11, 2001
    Messages:
    3,218
    Likes Received:
    0
    you can even use a coat hanger, if you wish. The standard practice, however, is to use 75 ohm video cable, or, if you want to avoid ground loops, toslink.
     
  3. Bob McElfresh

    Bob McElfresh Producer

    Joined:
    May 22, 1999
    Messages:
    5,182
    Likes Received:
    0
    Jeremy is correct. Coaxial-digital specifies a "75 ohm coaxial cable". Translation: a Video cable (usually with yellow bands on the RCA plugs).

    Audio cables can be made with 50/75/110/300 ohm coax. And people have used audio cables by mistake and it appears to work. But then they notice something: occasional audio drop-outs. Sometimes only once every 15 minutes, sometimes several in a minute. (One member was about to return his new system because it was bugging him so much before we determined he was using a RCA cable from a L/R set.)

    The coat-hanger trick - this does work. But only on a lab-bench with little or no other electrical devices nearby. To protect the weak, line-level signals you need a coaxial cable.

    Hope this helps.
     
  4. homthtr

    homthtr Supporting Actor

    Joined:
    Sep 5, 2006
    Messages:
    519
    Likes Received:
    0
    A cheap way to do that is to use a good quality RG6 Coax, A short piece that has Compression (snap n seal) F type coax connectors. The same ones that the cable or sattelite company make up on site. Just get 2 f-rca adaptors for about $4-$5 and your good to go. The Rg6 Coax is a great sheilded coax Digital connection.
     
  5. sarah99

    sarah99 Agent

    Joined:
    Aug 29, 2006
    Messages:
    41
    Likes Received:
    0

    But as you all know, once a 50 ohm RCA plug is on each end, the 75 ohm cable has an effective impedance of its' lowest value component ........ 50 ohms. So why not use any (50 ohm) cable to start with.

    (if you really needed 75 ohm impedance, the manufacturers would have fitted your equipment with BNC connectors)
     
  6. ChrisWiggles

    ChrisWiggles Producer

    Joined:
    Aug 19, 2002
    Messages:
    4,791
    Likes Received:
    1
    RCA plugs can approach 75ohm, though it is certainly true that BNC would be preferred.

    Any 75ohm cables are appropriate. Thankfully 75ohm cables are cheap and readily available at any radioshack, hardware store, electronics store, the net etc.

    If you want the very best pro grade stuff, that is also quit reasonable from someone like bluejeans.com.
     
  7. Bob McElfresh

    Bob McElfresh Producer

    Joined:
    May 22, 1999
    Messages:
    5,182
    Likes Received:
    0

    I wish that were true. All analog video connections need to be 75 ohms. But consumer gear is stuck with the old friction-fit RCA plugs. Pro gear and some projectors do have BNC jacks. Even the cheap-as-dirt "F" connector on your CATV cable is a better connector for high-frequency signals than an RCA plug. But we are stuck with this.
     

Share This Page